Using General Extrusion Operators to Model Periodic Structures

by Walter Frei(August 11, 2015)

In the course of building multiphysics models, we often encounter situations in which the solution to one physics is periodic — or very nearly so — while the solutions to other physics of interest are nonperiodic. If we know this ahead of time, it is possible to exploit the periodicity to reduce computational requirements. Here, we will demonstrate how to accomplish this using the General Extrusion component couplings in COMSOL Multiphysics.

Exploiting Periodicity in the Multiphysics Modeling of a Microfluidic Device

Let’s begin by looking at a microfluidic device, as shown below. Such devices feature small channels that are filled with fluids carrying different chemical species. Within their design, a common goal is to achieve optimal mixing within a small surface area, hence the serpentine channel.

Using General Extrusion Operators to Model Periodic Structures插图
A typical microfluidic device. Image by IX-factory STK — Own work, via Wikimedia Commons.

The schematic below illustrates that there are two fluid inlets, both of which carry the same solvent (water) but a different solute. At the outlet, we want the species to be well mixed. To model such a situation, we want to solve the Navier-Stokes equations for the flow. This computed flow field can then be used as input for the convection-diffusion equation governing the species concentration. The Micromixer tutorial, available in our Application Gallery, is an example of such a model.

Now, if desired, it is possible to model the entire device shown above. However, if we neglect the structure near the inlet and the outlet, we can reasonably assume that the flow within the channel bends will be identical between the unit cells. Therefore, we can greatly reduce our model by solving only for the fluid flow within one unit cell and patterning this flow solution throughout the modeling domain for the convection-diffusion problem.

Using General Extrusion Operators to Model Periodic Structures插图1
Schematic of a microfluidic mixer that depicts the repeated unit cell and the inlet and outlet zones.

For such a unit cell model, the walls of the channels are set to the Wall, No Slip condition. The Periodic Flow condition is used to set the velocity so it is identical at the inlet and outlet boundaries, allowing us to specify a pressure drop over a single unit cell. A pressure constraint at a single point is used to gauge fix the pressure field. The working fluid is water with properties defined at room temperature and pressure. The flow solution on this unit cell is also plotted, as shown below.

Using General Extrusion Operators to Model Periodic Structures插图2
The periodic modeling domain and the fluid flow solution.

Now that we have the solution on one unit cell, we can use the General Extrusion component coupling to map the solution from this one unit cell onto the repeated domains. This will enable us to define the flow field in the entire serpentine section.

Using General Extrusion Component Couplings to Pattern and Reuse the Solution

The General Extrusion feature is available in the model tree under Component > Definitions > Component Coupling. The settings for this feature are illustrated below. To map the solution from one domain into the other domains that are offset by a known displacement along the x-axis, the destination map uses the expression “x-Disp” for the x-expression. Thus, every point in the original domain is mapped along the positive x-direction by the specified displacement. Since there is no displacement in the y-direction, the y-expression is set at its default “y”.

The variable Disp is individually defined within each of the three domains, as shown in the figure below. Therefore, only a single operator is needed to map the velocity field into all of the domains. Within the original domain, a displacement of zero is used.

The settings for the General Extrusion operator and the definitions of the variable in the three domains.

With the General Extrusion operator defined, we can now use it throughout the model. In this example, the operator is used by the Transport of Diluted Species interface to define the velocity field (illustrated below). The velocity field is given by u and v, the fluid velocity in the x– and y-directions, respectively. The components of this velocity field are now defined in all of the repeated domains via the General Extrusion operator: genext1(u) and genext1(v), respectively.

Using General Extrusion Operators to Model Periodic Structures插图3
The General Extrusion operator is used to define the velocity field in all three periodic domains.

Now that the velocity field is defined throughout the modeling domain, the species concentration at the inlet is defined via the Inflow boundary condition. This applies a varying species concentration over the inlet boundary. An Outlet boundary condition is applied at the other end.

Although it is not strictly necessary to do so, the mesh is copied from the one domain used to solve for the fluid flow to all of the other domains. The Copy Domain mesh feature can copy the mesh exactly, thereby avoiding any interpolation of the flow solution between meshes.

The model is solved in two steps — first, the Laminar Flow physics interface is solved, and then the Transport of Diluted Species interface is solved. This is reasonable to do since it is assumed that the flow field is independent of the species concentration. The results of the analysis, including the concentration and the mapped velocity field, are depicted below.

Using General Extrusion Operators to Model Periodic Structures插图4
The species concentration (shown in color) is solved in all three repeating domains. The periodic velocity field, indicated by the arrows, is solved in one domain and mapped into the others.

Closing Remarks

We have discussed how the General Extrusion component coupling can be used to set up a linear pattern of a periodic solution as part of a multiphysics analysis. For circular periodicity, a rotation matrix, not a linear shift, must be used in the destination map. An example of defining such a rotation matrix is detailed in this previous blog post.

The approach we have applied here is appropriate for any instance in which a spatially repeating solution needs to be utilized by other physics. Where might you use it in your multiphysics modeling?

清醒 专注 努力
文章: 499


  1. […] 建模实现开始于在出口边界定义一个名为 genext1 的广义拉伸组件耦合。通过指定沿 x 轴的位移,这种耦合简单地将出口边界处的场映射回入口边界,该方法类似于之前博客文章中的方法。 […]


Captcha Code